The two methods don't belong in BinaryFunction methods.
Move the dispatch tables into target-specific MCPlusBuilder methods.
Reviewed By: rafauler
Differential Revision: https://reviews.llvm.org/D131813
Pre-calculate the register size table in MCPlusBuilder constructor,
similar to `AliasMap`/`SmallerAliasMap` in `initAliases`.
Reviewed By: #bolt, rafauler
Differential Revision: https://reviews.llvm.org/D145828
It was using a redundant iteration over super regs to build
SmallerAliasMap. Removing this results in exactly the same alias maps
and a noticeable performance gain on targets with a large number of
registers.
Just anecdotally: on my machine, processing a small AArch64 binary went
from 2.7s down to 80ms.
Reviewed By: Amir
Differential Revision: https://reviews.llvm.org/D145779
This patch fixes few problems with supporting dynamic relocations in CI.
1. After dynamic relocations and functions were read search for dynamic
relocations located in functions. Currently we expected them only to be
relative and only to be in constant island. Mark islands of such
functions to have dynamic relocations and create CI access symbol on the
relocation offset, so the BD would be created for such place.
2. During function disassemble and handling address reference for
constant island check if the referred external CI has dynamic
relocation. And if it has one we would continue to refer original CI
rather then creating a local copy.
3. After function disassembly stage mark function that has dynamic reloc
in CI as non-simple. We don't want such functions to be optimized, since
such passes as split function would create 2 copies of CI which we
unable to support currently.
4. During updating output values for BF search for BD located in CI and
update their output locations.
5. On dynamic relocation patching stage search for binary data located
on relocation offset. If it was moved use new relocation offset value
rather then an old one.
Vladislav Khmelevsky,
Advanced Software Technology Lab, Huawei
Differential Revision: https://reviews.llvm.org/D143748
In case of a function with unknown control flow but with a single jump
table and a single jump table site, we attempt to match the jump table
and a site and update block successors using jump table targets.
Restrict this behavior for split jump tables which have targets in a
fragment function.
Fixes https://github.com/llvm/llvm-project/issues/60795.
Reviewed By: #bolt, rafauler
Differential Revision: https://reviews.llvm.org/D144602
ICF optimization runs multiple passes and the order in which functions
are folded could be dependent on the order they are being processed.
This order is indeterministic as functions are intermediately stored in
std::unordered_map<>. Note that this order is mostly stable, but is not
guaranteed to be and can change e.g. after switching to a different C++
library implementation.
Because the processing (and folding) order is indeterministic, the
previous way of calculating merged function call count could produce
different results.
Change the way we calculate the ICF call count to make it independent of
the function folding/processing order.
Mostly NFC as the output binary should remain the same, the change
affects only the console output.
Reviewed By: yota9
Differential Revision: https://reviews.llvm.org/D144807
When createInstrumentedIndirectCall() was invoked for tail calls, we
attached annotation instruction twice to the new call instruction.
First in createDirectCall(), and then again while copying over the
metadata operands.
As a result, the annotations were not properly stripped for such calls
before the call to freeAnnotations() in LowerAnnotations pass. That lead
to use-after-free while restoring the offsets with setOffset() call.
Reviewed By: yota9
Differential Revision: https://reviews.llvm.org/D144806
`isChildOf` is a more concise name for the check. Also, there's no need to
test if the function is a fragment before doing `isChildOf` check.
Reviewed By: #bolt, rafauler, maksfb
Differential Revision: https://reviews.llvm.org/D142667
In lite mode, include split function fragments to the list of functions to
process even if a fragment has no samples. This is required to properly
detect and update split jump tables (jump tables that contain pointers to code
in the main and cold fragments).
Reviewed By: #bolt, maksfb
Differential Revision: https://reviews.llvm.org/D140457
In some binaries produced with ThinLTO there are CUs that share entry in
.debug_addr. Before we would generate a new entry for each. Which lead to binary
size increase. This changes the behavior so that we re-use entries in
.debug_addr.
Reviewed By: maksfb
Differential Revision: https://reviews.llvm.org/D142425
Changed contribution data structure to 64 bit. I added the 32bit and 64bit
accessors to make it explicit where we use 32bit and where we use 64bit. Also to
make sure sure we catch all the cases where this data structure is used.
Reviewed By: dblaikie
Differential Revision: https://reviews.llvm.org/D139379
Changed contribution data structure to 64 bit. I added the 32bit and 64bit
accessors to make it explicit where we use 32bit and where we use 64bit. Also to
make sure sure we catch all the cases where this data structure is used.
Reviewed By: dblaikie
Differential Revision: https://reviews.llvm.org/D139379
Before we always used DW_RLE_startx_length. This is not very efficient and leads
to bigger .debug_addr section. Changed it to use
DW_RLE_base_addressx/DW_RLE_offset_pair.
clang-16 build in debug mode
llvm-bolt ran on it with --update-debug-sections
| section | before | after | diff | % decrease |
| .debug_rnglists | 32732292 | 31986051 | -746241 | 2.3% |
| .debug_addr | 14415808 | 14184128 | -231680 | 1.6% |
Reviewed By: maksfb
Differential Revision: https://reviews.llvm.org/D140439
Use llvm::reverse instead of `for (auto I = rbegin(), E = rend(); I != E; ++I)`
Reviewed By: #bolt, rafauler
Differential Revision: https://reviews.llvm.org/D140516
Linker might relax adrp + ldr got address loading to adrp + add for
local non-preemptible symbols (e.g. hidden/protected symbols in
executable). As usually linker doesn't change relocations properly after
relaxation, so we have to handle such cases by ourselves. To do that
during relocations reading we change LD64 reloc to ADD if instruction
mismatch found and introduce FixRelaxationPass that searches for ADRP+ADD
pairs and after performing some checks we're replacing ADRP target symbol
to already fixed ADDs one.
Vladislav Khmelevsky,
Advanced Software Technology Lab, Huawei
Differential Revision: https://reviews.llvm.org/D138097
This is a fairly large changeset, but it can be broken into a few
pieces:
- `llvm/Support/*TargetParser*` are all moved from the LLVM Support
component into a new LLVM Component called "TargetParser". This
potentially enables using tablegen to maintain this information, as
is shown in https://reviews.llvm.org/D137517. This cannot currently
be done, as llvm-tblgen relies on LLVM's Support component.
- This also moves two files from Support which use and depend on
information in the TargetParser:
- `llvm/Support/Host.{h,cpp}` which contains functions for inspecting
the current Host machine for info about it, primarily to support
getting the host triple, but also for `-mcpu=native` support in e.g.
Clang. This is fairly tightly intertwined with the information in
`X86TargetParser.h`, so keeping them in the same component makes
sense.
- `llvm/ADT/Triple.h` and `llvm/Support/Triple.cpp`, which contains
the target triple parser and representation. This is very intertwined
with the Arm target parser, because the arm architecture version
appears in canonical triples on arm platforms.
- I moved the relevant unittests to their own directory.
And so, we end up with a single component that has all the information
about the following, which to me seems like a unified component:
- Triples that LLVM Knows about
- Architecture names and CPUs that LLVM knows about
- CPU detection logic for LLVM
Given this, I have also moved `RISCVISAInfo.h` into this component, as
it seems to me to be part of that same set of functionality.
If you get link errors in your components after this patch, you likely
need to add TargetParser into LLVM_LINK_COMPONENTS in CMake.
Differential Revision: https://reviews.llvm.org/D137838
With ThinLTO mutliple CUs can share the same .debug_str_offsets contribution. We
were creating a new one for each CU. This lead to a binary size increase.
Reviewed By: maksfb
Differential Revision: https://reviews.llvm.org/D139214
Summary:
Changed contribution data structure to 64 bit. I added the 32bit and 64bit
accessors to make it explicit where we use 32bit and where we use 64bit. Also to
make sure sure we catch all the cases where this data structure is used.
This patch mechanically replaces None with std::nullopt where the
compiler would warn if None were deprecated. The intent is to reduce
the amount of manual work required in migrating from Optional to
std::optional.
This is part of an effort to migrate from llvm::Optional to
std::optional:
https://discourse.llvm.org/t/deprecating-llvm-optional-x-hasvalue-getvalue-getvalueor/63716
This patch makes code less readable but it will clean itself after all functions are converted.
Differential Revision: https://reviews.llvm.org/D138665
This has the following advantages:
- std::shared_timed_mutex is macOS 10.12+ only. llvm::sys::RWMutex
automatically switches to a different implementation internally
when targeting older macOS versions.
- bolt only needs std::shared_mutex, not std::shared_timed_mutex.
llvm::sys::RWMutex automatically uses std::shared_mutex internally
where available.
std::shared_mutex and RWMutex have the same API, so no code changes
other than types and includes are needed.
Differential Revision: https://reviews.llvm.org/D138423
This patch replaces NoneType() and NoneType::None with None in
preparation for migration from llvm::Optional to std::optional.
In the std::optional world, we are not guranteed to be able to
default-construct std::nullopt_t or peek what's inside it, so neither
NoneType() nor NoneType::None has a corresponding expression in the
std::optional world.
Once we consistently use None, we should even be able to replace the
contents of llvm/include/llvm/ADT/None.h with something like:
using NoneType = std::nullopt_t;
inline constexpr std::nullopt_t None = std::nullopt;
to ease the migration from llvm::Optional to std::optional.
Differential Revision: https://reviews.llvm.org/D138376
