default implementation for x86, going through the stack in a similr
fashion to how the codegen implements BUILD_VECTOR. Eventually this
will get matched to VINSERTF128 if AVX is available.
llvm-svn: 124307
implementation of EXTRACT_SUBVECTOR for x86, going through the stack
in a similr fashion to how the codegen implements BUILD_VECTOR.
Eventually this will get matched to VEXTRACTF128 if AVX is available.
llvm-svn: 124292
clang's -Wuninitialized-experimental warning.
While these don't look like real bugs, clang's
-Wuninitialized-experimental analysis is stricter
than GCC's, and these fixes have the benefit
of being general nice cleanups.
llvm-svn: 124073
DAG. Disable using "-disable-sched-cycles".
For ARM, this enables a framework for modeling the cpu pipeline and
counting stalls. It also activates several heuristics to drive
scheduling based on the model. Scheduling is inherently imprecise at
this stage, and until spilling is improved it may defeat attempts to
schedule. However, this framework provides greater control over
tuning codegen.
Although the flag is not target-specific, it should have very little
affect on the default scheduler used by x86. The only two changes that
affect x86 are:
- scheduling a high-latency operation bumps the current cycle so independent
operations can have their latency covered. i.e. two independent 4
cycle operations can produce results in 4 cycles, not 8 cycles.
- Two operations with equal register pressure impact and no
latency-based stalls on their uses will be prioritized by depth before height
(height is irrelevant if no stalls occur in the schedule below this point).
llvm-svn: 123971
flags. They are still not enable in this revision.
Added TargetInstrInfo::isZeroCost() to fix a fundamental problem with
the scheduler's model of operand latency in the selection DAG.
Generalized unit tests to work with sched-cycles.
llvm-svn: 123969
The value mapping gets confused about which original values have multiple new
definitions so they may need phi insertions.
This could probably be simplified by letting enterIntvBefore() take a live range
to be added following the instruction. As long as the range stays inside the
same basic block, value mapping shouldn't be a problem.
llvm-svn: 123926
to add/sub by doing the normal operation and then checking for overflow
afterwards. This generally relies on the DAG handling the later invalid
operations as well.
Fixes the 64-bit part of rdar://8622122 and rdar://8774702.
llvm-svn: 123908
TargetInstrInfo:
Change produceSameValue() to take MachineRegisterInfo as an optional argument.
When in SSA form, targets can use it to make more aggressive equality analysis.
Machine LICM:
1. Eliminate isLoadFromConstantMemory, use MI.isInvariantLoad instead.
2. Fix a bug which prevent CSE of instructions which are not re-materializable.
3. Use improved form of produceSameValue.
ARM:
1. Teach ARM produceSameValue to look pass some PIC labels.
2. Look for operands from different loads of different constant pool entries
which have same values.
3. Re-implement PIC GA materialization using movw + movt. Combine the pair with
a "add pc" or "ldr [pc]" to form pseudo instructions. This makes it possible
to re-materialize the instruction, allow machine LICM to hoist the set of
instructions out of the loop and make it possible to CSE them. It's a bit
hacky, but it significantly improve code quality.
4. Some minor bug fixes as well.
With the fixes, using movw + movt to materialize GAs significantly outperform the
load from constantpool method. 186.crafty and 255.vortex improved > 20%, 254.gap
and 176.gcc ~10%.
llvm-svn: 123905
Added a check for already live regs before claiming HighRegPressure.
Fixed a few cases of checking the wrong number of successors.
Added some tracing until these heuristics are better understood.
llvm-svn: 123892
with an invalid type then split the result and perform the overflow check
normally.
Fixes the 32-bit parts of rdar://8622122 and rdar://8774702.
llvm-svn: 123864
interval after an instruction. The leaveIntvAfter() method only adds liveness
from the instruction's boundary index to the inserted copy.
Ideally, SplitKit should be smarter about this, perhaps by combining useIntv()
and leaveIntvAfter() into one method that guarantees continuity.
llvm-svn: 123858
Region splitting includes loop splitting as a subset, and it is more generic.
The splitting heuristics for variables that are live in more than one block are
now:
1. Try to create a region that covers multiple basic blocks.
2. Try to create a new live range for each block with multiple uses.
3. Spill.
Steps 2 and 3 are similar to what the standard spiller is doing.
llvm-svn: 123853
Analyze the live range's behavior entering and leaving basic blocks. Compute an
interference pattern for each allocation candidate, and use SpillPlacement to
find an optimal region where that register can be live.
This code is still not enabled.
llvm-svn: 123774
This shaves off 4 popcounts from the hacked 186.crafty source.
This is enabled even when a native popcount instruction is available. The
combined code is one operation longer but it should be faster nevertheless.
llvm-svn: 123621
http://graphics.stanford.edu/~seander/bithacks.html#CountBitsSetParallel
In a silly microbenchmark on a 65 nm core2 this is 1.5x faster than the old
code in 32 bit mode and about 2x faster in 64 bit mode. It's also a lot shorter,
especially when counting 64 bit population on a 32 bit target.
I hope this is fast enough to replace Kernighan-style counting loops even when
the input is rather sparse.
llvm-svn: 123547
